A diesel engine runs rough and smokes white for about a minute after a cold start. Resistance is measured at each glow plug terminal with the harness disconnected. Based on the readings shown, what is the cause?
On a 5°F morning, a diesel truck starts and idles, then loses power and stalls after a few miles on the highway. After an hour in a heated shop, it runs normally. Which of these could be the cause?
Right after both fuel filters are replaced, a common rail diesel cranks but will not start. It ran well before the service. What should the technician do first?
A rear crankshaft seal is replaced because of an oil leak. The old seal lip has worn a groove into the crankshaft flange where the lip rides. What is the repair?
A diesel engine pushes coolant into the overflow bottle and boils over when towing. The pressure cap is rated at 16 psi. Technician A says a cap holding slightly above 16 psi causes this. Technician B says a cap that opens at 9 psi causes this. Who is right?
A technician is servicing a diesel air cleaner that has a restriction indicator. The element looks dirty, but the indicator shows restriction well below its service limit. What should be done?
A technician is measuring cylinder 3 during an engine overhaul. Based on the measurement sheet shown, what is needed?
A diesel engine ticks at a cold start, and the tick fades as it warms up. Black soot streaks run from a seam near one cylinder, and boost is slightly low under load. Which of these could be the cause?
A technician is checking a harness connector for an intermittent injector circuit code. Technician A says terminal fit is checked by pushing a meter probe into each female terminal. Technician B says a female terminal with low drag is fixed by squeezing it with pliers. Who is right?
The high-pressure line between the pump and the rail on a common rail diesel leaks fuel at one fitting while the engine runs. Which is the LEAST likely result?
A customer says a diesel pickup loses power while pulling a trailer up long grades. In the shop, the engine idles smoothly, no codes are stored, and idle readings look normal. What should the technician do next?
A common rail diesel has low power and a rail pressure code. The readings shown were taken key on, engine off, after an overnight soak. What is the fault, and what is the repair?
A diesel truck with two batteries cranks slowly at 0°F and will not start. Cranking speed is 90 rpm. Which is the LEAST likely cause of the slow cranking speed?
A diesel engine with injectors mounted in sleeves (cups) is losing coolant with no external leak. After the injectors are removed, coolant is found in one injector bore. Which test confirms the leak source?
A technician is inspecting a viscous crankshaft vibration damper during a front cover reseal. Which finding is LEAST likely to require damper replacement?
A diesel truck with a diesel particulate filter (DPF) is running an active regeneration while driving on the highway. During the regeneration, all of these happen EXCEPT:
A diesel truck with a variable geometry turbocharger (VGT) has low power under load, with a boost-low code. Based on the scan data shown, what is the cause?
A diesel engine has a sharp knock at idle that gets louder under load. A scan tool cylinder cutout test is done at warm idle. Based on the results shown, what is the cause?
The water-in-fuel lamp comes on in a common rail diesel truck right after a fill-up at a rural station. Technician A says the water separator should be drained before the engine runs much farther. Technician B says water that reaches the high-pressure pump damages it through corrosion and poor lubrication. Who is right?
The dash oil pressure gauge on a diesel truck reads zero at all engine speeds, and the engine is quiet. A mechanical gauge teed into the oil gallery reads 40 psi at hot idle. Which of these could be the cause?
A turbocharger whines loudly, and oil is found in the intake duct after the compressor. The intake hose is removed for inspection. Technician A says compressor blade rub marks on the housing can point to worn shaft bearings. Technician B says high crankcase pressure can push oil out past the turbocharger seals. Who is right?
A diesel engine puts out white smoke for the first few minutes after a cold start. The smoke clears once the engine warms up. Technician A says unburned fuel from low combustion chamber temperature can cause this. Technician B says a restricted air filter element can cause this. Who is right?
The EGR valve on a light-duty diesel is stuck partly open and does not close when commanded. Which is the LEAST likely result?
A technician is choosing engine oil for a light-duty diesel whose manual calls for an API CK-4 oil. Technician A says an API FA-4 oil can be used wherever a CK-4 oil is specified. Technician B says a CK-4 oil can be used in an older engine that calls for CJ-4. Who is right?
A technician is checking camshaft end play on an overhead camshaft diesel cylinder head. Technician A says end play is read with a dial indicator while prying the camshaft fore and aft. Technician B says end play is read with plastic gauge across a camshaft bearing journal. Who is right?
Reading Your Results: A9 Light Vehicle Diesel Engines, Test 1
A score by itself only tells you whether you passed. What follows is how to read the questions you missed on this test, because the same wrong answer can mean two very different things, and the fix is different for each one.
This test has 25 questions, weighted across the ASE content areas the way the real exam is: General Diagnosis (5), Cylinder Head and Valve Train Diagnosis and Repair (2), Engine Block Diagnosis and Repair (3), Lubrication and Cooling Systems Diagnosis and Repair (3), Air Induction and Exhaust Systems Diagnosis and Repair (6), Fuel System Diagnosis and Repair (6). 5 of them include an exhibit to read before you answer. Every question has a full explanation in the review below, including why each wrong answer is wrong.
If you missed questions built on a reading or an exhibit
5 questions on this test hand you a measurement, a chart, a waveform, or a scan value and ask what it supports. The question is rarely what the number is. It is what that reading is capable of proving, and what it cannot prove no matter how clean it looks. Before you look at the options, decide whether the reading is in or out of specification and which part of the system it actually tests.
If you missed the Technician A and Technician B questions
There are 7 of these. Treat each technician's statement as its own true-or-false question and settle it before you look at the four answer choices. Most misses come from agreeing with a statement that is true in general but does not fit the exact condition in the stem, or from rejecting a correct statement because it sounds too simple.
If you missed the most likely cause questions
3 questions describe a symptom that several faults could produce, and only one answer fits every condition given. Read the conditions first: when it happens, what is normal, what has already been checked. Those details usually rule out two answers before you finish reading the options.
If you missed the EXCEPT and LEAST likely questions
This test contains 5 of them, and missing several is a reading problem rather than a knowledge problem. Before looking at the options, work out what the real causes would have in common, then find the one answer that does not share that trait. Finding the shared trait first turns a four-way guess into a one-way check.
If you missed the scenario and next-step questions
5 questions walk a complaint through to a cause or to the correct next step. These reward working in the order a good technician would: confirm the concern, use the information already given, and choose the test or repair that the evidence actually supports, not the one that is most expensive or most familiar.