An oil analysis on a short-trip diesel pickup shows low viscosity and 6% fuel. Sodium and potassium are normal, and the oil level is rising. Technician A says repeated interrupted DPF regenerations can raise fuel dilution. Technician B says the report can point to a coolant leak into the oil. Who is right?
On a 25°F day, a diesel pickup has poor heater output, and the temperature gauge stays low on the highway. Based on the warm-up readings shown, what is the cause?
A diesel truck loses power after long highway runs. When the fuel cap is removed, air rushes into the tank, and power returns. Technician A says a restricted fuel return line can cause this. Technician B says a plugged fuel tank vent can cause this. Who is right?
A diesel is hard to start below 20°F. Every glow plug is in spec. With glow commanded on by the ECM, the module has 12.4 V at its power feed terminal, but every plug gets 0 V. Which of these could be the cause?
A technician is adjusting valves on a diesel with adjustable valve bridges (crossheads) with adjusting screws, each opening two valves. Technician A says the bridge is set to press both valves evenly before lash is set. Technician B says valve lash is measured between the rocker arm and the bridge pad. Who is right?
A removed charge air cooler, capped at 30 psi, loses 9 psi in 15 seconds on three tests; the limit is 5 psi. Soapy water shows no bubbles at the caps or clamps. What is the result?
A diesel has a low-power concern. A bulletin adds new engine software for listed calibrations. The scan tool shows the engine already has the updated calibration ID the bulletin installs. What should the technician do next?
A common rail diesel has low power under load. A high-pressure test gauge is installed per the service procedure. Based on the readings shown, what is happening, and what is the next step?
A technician is checking a cast-iron diesel cylinder head after coolant was found in one cylinder. The head is clean, and no cracks are visible. Which test can find a hairline crack between the valve seats?
Oil is found at both the compressor outlet and the turbine outlet of a diesel turbocharger. Shaft play is within limits, the wheels do not rub, and crankcase pressure is normal. Which of these could be the cause?
Engine off, a diesel's absolute boost sensor and baro read 14.6 psia. At full load it reads 30 psia; a manifold gauge reads 15 psi. Technician A says the boost sensor is reading low under boost. Technician B says the boost sensor is reading accurately. Who is right?
A diesel pickup has a vibration that rises with engine speed. It is just as strong when the engine is revved in park as when driving. Which is the LEAST likely cause?
A technician is measuring piston protrusion with a dial indicator zeroed on the deck. The plunger sits near the thrust edge of the crown, and the reading changes 0.08 mm as the piston rocks at TDC. What should be done?
A diesel rattles from its timing gears at idle. With the cover off, a dial indicator on the cam gear face reads 0.012 in. as the gear is pried axially, in and out. What does this reading show?
A technician is finishing a cylinder 3 injector replacement on a common rail diesel. Technician A says the new injector code is entered for cylinder 3 with a scan tool. Technician B says leaving the old injector code causes uneven fueling in that cylinder. Who is right?
A diesel engine with a closed crankcase ventilation system is leaking oil at the dipstick tube and front seal. Based on the crankcase pressure readings shown, what is the cause?
A technician is installing main bearings in a diesel engine that uses select-fit bearing shells. Based on the codes and chart shown, which shell grade is needed for main journal 3?
A diesel with hydraulic electronic unit injectors (HEUI) cranks but will not start. Injection control pressure (ICP) is 250 psi while cranking against a 500 psi minimum. Which is the LEAST likely cause?
A diesel with an electric lift pump loses power at full load. There, supply pressure is 66 psi at the final filter inlet and 38 psi at its outlet. Lift pump specification is 60 to 70 psi. Which of these could be the cause?
A diesel serpentine belt wears on one edge and chirps at idle. The tensioner tests good. Technician A says a straightedge across the pulley faces can show misalignment. Technician B says the tensioner spring can cause this edge wear. Who is right?
Exhaust backpressure measured at the turbocharger outlet, ahead of the aftertreatment, is above specification at full load on a diesel truck. Which is the LEAST likely cause?
A rail pressure low code's freeze frame shows 2,300 rpm, 95% load and 160°F fuel. The diesel now idles normally, no active codes. Technician A says the normal idle data prove the fault is repaired. Technician B says freeze frame shows the fault is present now. Who is right?
A diesel with SCR and two NOx sensors sets a code for low NOx conversion efficiency. Any of these could cause it EXCEPT:
Three engine sensors that share one 5 V reference circuit all show implausible readings. The reference measures 1.8 V at a sensor connector. Which is the LEAST likely cause?
A diesel pickup is losing coolant with no external leaks. Based on the test results shown, what is the cause?
Reading Your Results: A9 Light Vehicle Diesel Engines, Test 2
A score by itself only tells you whether you passed. What follows is how to read the questions you missed on this test, because the same wrong answer can mean two very different things, and the fix is different for each one.
This test has 25 questions, weighted across the ASE content areas the way the real exam is: General Diagnosis (4), Cylinder Head and Valve Train Diagnosis and Repair (3), Engine Block Diagnosis and Repair (2), Lubrication and Cooling Systems Diagnosis and Repair (3), Air Induction and Exhaust Systems Diagnosis and Repair (6), Fuel System Diagnosis and Repair (7). 5 of them include an exhibit to read before you answer. Every question has a full explanation in the review below, including why each wrong answer is wrong.
If you missed questions built on a reading or an exhibit
5 questions on this test hand you a measurement, a chart, a waveform, or a scan value and ask what it supports. The question is rarely what the number is. It is what that reading is capable of proving, and what it cannot prove no matter how clean it looks. Before you look at the options, decide whether the reading is in or out of specification and which part of the system it actually tests.
If you missed the Technician A and Technician B questions
There are 7 of these. Treat each technician's statement as its own true-or-false question and settle it before you look at the four answer choices. Most misses come from agreeing with a statement that is true in general but does not fit the exact condition in the stem, or from rejecting a correct statement because it sounds too simple.
If you missed the most likely cause questions
3 questions describe a symptom that several faults could produce, and only one answer fits every condition given. Read the conditions first: when it happens, what is normal, what has already been checked. Those details usually rule out two answers before you finish reading the options.
If you missed the EXCEPT and LEAST likely questions
This test contains 5 of them, and missing several is a reading problem rather than a knowledge problem. Before looking at the options, work out what the real causes would have in common, then find the one answer that does not share that trait. Finding the shared trait first turns a four-way guess into a one-way check.
If you missed the scenario and next-step questions
5 questions walk a complaint through to a cause or to the correct next step. These reward working in the order a good technician would: confirm the concern, use the information already given, and choose the test or repair that the evidence actually supports, not the one that is most expensive or most familiar.